How To Use A Wood Cutter

The wood cutter is a rather complex device and can be dangerous if you do not use it correctly. You need to be very careful about how you mount the knives and make the adjustments, test the device before going to work, learn how to operate it properly and use the right accessories for diversity and safety. Also, take into account its maintenance, if you want to extend its life.

Do you own a wood cutter or do you intend to buy such a product and want to know a series of important information about its use? Read this text carefully to see some useful steps in installing and using it.

 

 

Install the milling cutter

For starters, all you have to do is install the knives. Be sure to perform the following steps in the order mentioned: make sure that the device is not connected to a power source; turn the cutter upside down; while holding down the button that locks the shaft, loosen the sleeve nut; insert inside the latter ¾ of the length of the knife leg; hold down the spindle lock button and tighten the sleeve nut back.
See, it’s not hard at all. You just have to have patience and a little skill.

 

Make the necessary adjustments

Before going to work, you must take care of making work adjustments on the cutter. Proceed as follows: check to see if the depth indicator rod is on the outside by about 3 mm; rotate the turret to fix the rod that has the maximum height until a click is heard, below the depth indicator; loosen the rosette so as to allow the rod of the depth indicator to fall on that of the turret stop; release the locking lever and press to make contact between the cutter and the workpiece; tighten the locking lever. Now your milling cutter is adjusted to 0 mm.
If you want other dimensions, here’s what you need to do: raise the depth indicator and adjust it to the desired value, squeezing the rosette when you have positioned everything as needed; release the release lever and allow the device to lift; use the depth stop turret for the desired settings.
All you have to do is connect a vacuum cleaner to the mill to collect the dirt and connect the device to a power supply.

 

Test to see if you installed everything as per the book

After you have mounted the knives and taken care of the adjustments, we suggest you test to see if everything is fine, on a piece of material that you no longer need. Such a practice is especially recommended for people working for the first time with such a device.

 

Be careful how you operate the device

On one of the handles you will find a safety button, which you must press in order to make the cuts. Press on it and gently leave the device on the material, until the depth indicator reaches the turret of the stop, tighten the lever and with both hands, drive the cutter in the direction you want. When you want to stop, you release the lever and so on.


Be very careful that when working, the piece of material is well fixed, so that it does not move while you act on it. Everything must be done carefully, smoothly, without forcing the device.
There are also a number of tips related to user safety. Here are some of the most important: operate the device in a well-lit area so that you can see exactly what you have to do; do not work in dirty areas, where there are flammable liquids or other substances that could become dangerous; do not use the device if you notice certain defects in terms of electrical safety, even if they are minor; do not use the cutter in environments where there is a lot of humidity or outdoors when it is raining outside; do not use this product if you are very tired, if you do not feel well or if you have consumed a larger amount of alcohol, because it can become quite dangerous if you are not very careful and focused.


Your safety is very important, which is why you do not ignore these aspects. There are others that you will surely find in the user manual that you will receive with the product.

 

Use the right accessories for what you need

The marks left by the cutter can be very diverse, depending on the knives you use. Get well informed and buy what you need to be able to process the wood as you wish.
Protective equipment could also be included in the category of accessories. In order to carry everything in complete safety, both the tests and the work itself require the use of these types of articles. You need glasses, so that various residues, helmets do not penetrate your eyes, if you work a lot with the device and it produces a very high noise and dust mask, to protect your airways.

 

Take care of the maintenance of the device – cleaning and lubrication

If you want your device to work well for as long as possible, then you need to take care of it. The following aspects are important:


Cleaning – is done with the appliance disconnected from the power source. After each use, wipe the dust cover with a dry cloth. Clean the ventilation mouth well to get rid of impurities. If the dirt is thicker in some areas, you can use a damp cloth on the outside, soaked in soap and water beforehand.
Abrasive solutions, based on solvents or those containing gasoline, alcohol or ammonia are not recommended.


Lubrication – some milling cutters may need to be greased from time to time. With what and at what periods? You will be told in the manual, depending on the model you choose. It is also possible to buy a device that does not require such action.


This is some of the most important information you need to know when you plan to use a wood cutter . Take them into account and act accordingly. If you want to buy such a product, first check the offers in online stores.

 

Leave a Comment